1 00:00:00,470 --> 00:00:02,990 So let's create our first project in Jeunesse three. 2 00:00:04,250 --> 00:00:10,070 Now, at this point, we have a choice to make, so whether we run against three on the local server 3 00:00:10,100 --> 00:00:11,900 or within a virtual machine. 4 00:00:13,160 --> 00:00:19,700 Because the primary reason for using Gen3 is simulating a network with switches and routers, all we 5 00:00:19,700 --> 00:00:22,910 have to do is select the run only legacy. 6 00:00:22,940 --> 00:00:24,920 I was on my computer. 7 00:00:25,400 --> 00:00:28,040 That's the option which is not selected by default. 8 00:00:30,120 --> 00:00:32,910 So we leave this page with the rest of the default values. 9 00:00:35,970 --> 00:00:42,780 It asked for the permission for Newbridge to interact with a network interface, so click yes to allow 10 00:00:43,110 --> 00:00:44,790 and enter the admin password. 11 00:00:46,180 --> 00:00:52,750 Local server is started up and Ginés three connected to it successfully, so click next. 12 00:00:53,830 --> 00:00:59,680 Finally, we have a summary of the project settings, so click finish to end, the project said. 13 00:01:01,620 --> 00:01:06,180 So as soon as you click finish the new appliance template window appears. 14 00:01:06,620 --> 00:01:12,290 So this point, we're going to add an iOS router using a real iOS image. 15 00:01:12,450 --> 00:01:15,690 So select the option and click, OK? 16 00:01:16,860 --> 00:01:23,730 So I'm assuming that you were a first time user of Jeunesse three, and as such, you need to be aware 17 00:01:23,730 --> 00:01:30,240 that in order to use this application software, at the minimum, you need to download one more piece 18 00:01:30,240 --> 00:01:30,890 of software. 19 00:01:31,680 --> 00:01:36,930 So you already downloaded and install the G.A. three software itself, which actually comes bundled 20 00:01:36,930 --> 00:01:39,270 with a whole bunch of other stuff which isn't really needed. 21 00:01:39,540 --> 00:01:45,060 And then you're also going to download at least one Cisco iOS software image. 22 00:01:45,900 --> 00:01:51,780 I would suggest that you would get hold of software images that support either the thirty seven twenty 23 00:01:51,780 --> 00:01:56,160 five series router or the thirty seven forty five series router. 24 00:01:57,200 --> 00:02:00,470 If you can get hold of these, that'll be the best. 25 00:02:01,670 --> 00:02:09,590 So if you don't know anything about Cisco routers at all, you're just looking for some advice on which 26 00:02:09,590 --> 00:02:16,850 particular one to choose for your iOS image, I would select a 37, 25 or 30 745 image. 27 00:02:17,540 --> 00:02:23,270 If you get software images for one that's already 700 series of routers, that comes along with like 28 00:02:23,270 --> 00:02:27,700 a switching module, you don't have to download anything else. 29 00:02:28,010 --> 00:02:29,510 There's nothing that you have to do. 30 00:02:29,750 --> 00:02:35,180 But basically you can turn on a switch that operates within or inside of that router. 31 00:02:35,540 --> 00:02:37,820 And then I can do this switching and routing. 32 00:02:38,270 --> 00:02:41,570 Most of the other platforms do not support that. 33 00:02:42,600 --> 00:02:47,550 So in my particular case, I'm going to use a 37 25 image. 34 00:02:49,110 --> 00:02:56,940 And now I get to the point when we get to choose what iOS image we want to import into Gen3, and here 35 00:02:56,940 --> 00:03:02,040 is where you get to browse for wherever you've downloaded the Cisco is software, too. 36 00:03:02,640 --> 00:03:06,260 I'm going to use a 37 25 image, which I've already downloaded. 37 00:03:07,020 --> 00:03:13,920 If you don't have it already, please search for the keywords such as Cisco, iOS 37 25 Image Download 38 00:03:14,430 --> 00:03:17,300 and you'll find an image and then download it for yourself. 39 00:03:18,310 --> 00:03:23,560 I'd love to show it to you, but I don't want to mess with legal issues, it's not so hard and I'm sure 40 00:03:23,560 --> 00:03:24,700 that you can easily find one. 41 00:03:25,940 --> 00:03:31,620 Now click Browse to select the iOS image, so let me find my image. 42 00:03:31,640 --> 00:03:32,000 Here it is. 43 00:03:33,920 --> 00:03:35,690 Select it and click open. 44 00:03:36,930 --> 00:03:39,660 And yes, I would like to decompress the image. 45 00:03:42,610 --> 00:03:50,650 So click next, give a name and make it up, whatever you want, I'm going to choose C 37 25. 46 00:03:50,650 --> 00:03:51,910 That's pretty good for me. 47 00:03:52,630 --> 00:03:59,260 So now before I leave the screen, there's also a little box here that says this is an ether's switch 48 00:03:59,260 --> 00:03:59,770 router. 49 00:03:59,800 --> 00:04:05,530 So you can just have every router in your topology as in either switch. 50 00:04:05,970 --> 00:04:08,200 I'm going to leave that unchecked for now. 51 00:04:08,440 --> 00:04:10,840 Will create a legacy router right now. 52 00:04:12,560 --> 00:04:18,500 So make the default RAM 256 megabytes and then click next. 53 00:04:19,460 --> 00:04:24,910 So here's where I get to select what modules or port adapters I want in my chest. 54 00:04:26,110 --> 00:04:33,970 It comes with a fast Ethernet slot already on it, and now I've selected in another slot so I can put 55 00:04:34,420 --> 00:04:38,660 another fast Ethernet card and then I'll put another fast Ethernet card. 56 00:04:38,860 --> 00:04:39,360 Why not? 57 00:04:39,850 --> 00:04:43,810 So as I go forward, I've got some WEC slots available. 58 00:04:45,120 --> 00:04:50,760 Once again, these slots are available in the 37 25, depending upon that software that you're using, 59 00:04:50,970 --> 00:04:53,210 you might not have all of these available to you. 60 00:04:54,540 --> 00:04:58,980 So I'm going to put some serial interfaces in these slots. 61 00:04:58,980 --> 00:05:06,780 So I'm going to have tons of interfaces in every single one of my routers to give me lots of flexibility 62 00:05:06,780 --> 00:05:09,960 in the types of typologies that I want to design. 63 00:05:10,770 --> 00:05:11,310 Don't worry. 64 00:05:11,310 --> 00:05:14,420 I mean, we can change all these settings after the set up as well. 65 00:05:15,730 --> 00:05:16,840 So now click next. 66 00:05:19,440 --> 00:05:26,010 Now, I don't want to waste time for the idle PC, we can simply say that it's used to make the CPU 67 00:05:26,010 --> 00:05:27,840 usage much more effective. 68 00:05:27,870 --> 00:05:34,890 So just click idle PC finder and let gainst three find one for you. 69 00:05:36,230 --> 00:05:37,730 And now we can hit finish. 70 00:05:42,220 --> 00:05:44,350 And a router is available to us. 71 00:05:45,350 --> 00:05:47,810 Now we can use it in our virtual topology. 72 00:05:49,410 --> 00:05:57,900 All right, so here are the preferences of Jeunesse three, the rooters added under the Dynamics Iowas 73 00:05:57,900 --> 00:06:03,270 rooters menu, you can see the menu on the tree at the left hand side of the window. 74 00:06:03,280 --> 00:06:06,330 So click OK to close the preferences window. 75 00:06:07,930 --> 00:06:15,460 Now is the time to name our first Ganzouri project, as you can see here, the project location changes 76 00:06:15,460 --> 00:06:18,070 as well when you change the project name. 77 00:06:18,070 --> 00:06:20,620 So click OK once you've finished naming it. 78 00:06:21,550 --> 00:06:24,370 And this is your main Ganzouri window. 79 00:06:25,500 --> 00:06:31,890 So now let's create another Iooss router template and make it and either switch router this time around. 80 00:06:33,050 --> 00:06:39,530 Now from the GNC, three main menu, select preferences from the left hand side menu, select Iommi 81 00:06:39,530 --> 00:06:46,880 rooters under the Dynamics Submenu and click knew we can use our existing image right now. 82 00:06:46,940 --> 00:06:47,990 So click next. 83 00:06:49,310 --> 00:06:55,070 And I'd like to turn this router into a switch by selecting the ether's switch box, let's go ahead 84 00:06:55,070 --> 00:06:57,890 and change the RAM to 256 megabytes. 85 00:06:59,340 --> 00:07:04,800 So now you can see it automatically populates one of those slots with a 16 point switch module. 86 00:07:04,830 --> 00:07:07,680 And if you want, you can just leave it that way. 87 00:07:07,830 --> 00:07:14,580 If the only thing that you're planning in the router is for six port Ethernet switch, but. 88 00:07:15,450 --> 00:07:21,090 What I want to do is add more flexibility, so I'm going to add some more slots, just like the previous 89 00:07:21,090 --> 00:07:21,660 scenario. 90 00:07:23,250 --> 00:07:25,290 Let the app find an idle PC. 91 00:07:35,800 --> 00:07:37,010 And then click finish. 92 00:07:38,080 --> 00:07:40,450 Now we have two different router templates. 93 00:07:40,480 --> 00:07:45,280 The first one is the classic router and the second one is any other switch router. 94 00:07:46,000 --> 00:07:52,480 Now you can click edit to remove or add new slides, change a name, change your size, whatever you 95 00:07:52,480 --> 00:07:53,590 want to do to customize it.